Job Profile: A respected Western NSW Abattoir was having
problems with slippery stair and floor surfaces.
All their stairs and floor surfaces were
coated with a DFT 1.0mm and Ultimate Non Slip Particles for
a Non Slip finish that is guaranteed for maximum performance
up to 10 years+ for vehicular/Forklift Traffic.
Job Profile: A respected Western
NSW Abattoir was having problems with corrosion attacking
there Chutes and equipment.
Their process equipment was coated with Ultimate
1601, (High Gloss, All Purpose Ceramic Composite), Colour:
Safety Yellow, after been properly prepared by our professional
team. A DFT of 500 microns was applied which will enhance
performance and service life for many years.
Before
After
Company: Roland Graf Auto (Cairns)
Project: Vehicle window tint shed
Problem: Window tinting
requires usage of water and detergent which ends up on the
floor causing a damp and slippery surface. We required a non
slip, water proof and durable surface, Ultimate Ceramic Coatings
not only fitted the criteria but was the cheaper alternative.
Being a rhino lining dealer we wanted to incorporate the 2
products. The majority of the area will be Ultimate 1601 ceramic
coatings and the area were the workers prep their tint would
be Rhino linings Dura spray. Total area 100 m2
Before
After
 |
Dark gray is Rhino Lining and light gray is ceramic |
 |
Conclusion
Very satisfied with the Ultimate Ceramic Coating, easy to
use and gives the cheaper avenue for floor coatings while
still covering the criteria.
Project: Ceramic
Composite Pool
Category: Wear & Osmosis Resistant
Completion Date: September 2007
Ceramic Composite Swimming Pool |
Ceramic Composite Swimming Pool |
|
Project Description:
-
This project involved involved a used
Fibreglass swimming pool that suffered Osmosis and was
in dire straits for a new Look.
-
All osmosis was cut away and replaced
With Ultimate 1202 (Ceramic Paste) and Coated with Ultimate
1601 (All Purpose), to Give this pool the ULTIMATE LOOK.
-
This pool is now protected with a
fully Engineered Ceramic Composite, that will last for
many years.
Ultimate
1101
Wear Resistant Trowellable composite
Company:
Continental Conveyors & Equipment Pty Ltd
Project: Coal Chutes
Product: Ultimate 1101 (Fine)
Completion Date: May 2007
Description:
Continental Conveyors & Equipment Pty
Ltd was utilising another product which came in 3 parts, A,B
and a primer. The product was to time consuming to apply.
The overall process became too time consuming. Ultimate1101
(Fine) was purchased, which meant no primer required and the
low tech application, with diamond like hardness, which enabled
better wear performance for the client.
Overall Continental Conveyors has given the
thumbs up, and further chutes to be applied with Ultimate
Ceramic Coatings – Ultimate1101 (Fine).
Ultimate
1001
Sprayable Reinforced Protective Composite
Project: Salt
Processing Tanks
Category: Corrosion & Wear Resistance
Project Description:
- The project involved one of the biggest Mining Companies
in Australia, which needed a solution to their corrosion
and wear problems with their Process Tanks.
- A Class 2.5 Blast Profile – AS1627.4 (75 –
125um) was applied to the stainless steel surfaces, for
maximum performance and adhesion.
- Ultimate 1001 (Advanced Polymer Resin), was applied at
a nominal thickness of 750um for an, impermeable, abrasion
and corrosion resistant composite lining.
- This Mining Company can be confident that their processing
equipment has the “ULTIMATE PROTECTION”, eliminating
all CORROSION and WEAR for many years. Therefore “SAVING
TIME & MONEY”.
Project: Gorman
Rupp T6 – Seal Plate
Category: Corrosion & Wear Resistance
Completion Date: October 2007
Gorman Rupp T6 Seal Plate (Before) |
Gorman Rupp T6 Seal Plate (After) – Ultimate
1001 |
|
Project Description:
-
This project involved a leading Pump
Service and Sales Company, which needed a solution to
their Gorman Rupp T6 series Pump Seal Plate for corrosion
& wear.
-
A Class 2.5 Blast profile –
AS1627-4 (75 -125um) was applied for maximum adhesion,
and then coated with Ultimate 1001.
-
This Gorman Rupp T6 Seal Plate will
perform better with an extended life & reduced maintenance
costs, therefore: “SAVING TIME & MONEY”
Company: Norco
Milk (Coffs Harbour)
Project: Blow Mould Cap Ends
Category: Corrosion & Wear Resistance
Completion Date: November 2007.
 |
 |
Blow Mould Cap Ends (After) – Ultimate 1001 |
Project Description:
-
This project involved a leading Milk
Company, which needed a solution to their Blow Mould Cap
Ends for corrosion & wear.
-
A Class 2.5 Blast profile –
AS1627-4 (75 -125um) was applied for maximum adhesion,
and then coated with Ultimate 1001.
-
These Blow Mould Cap Ends will perform
better with an extended life & reduced maintenance
costs, therefore: “SAVING TIME & MONEY”
Ultimate
CR98
Reinforced Composite Protective Coating, with extreme Chemical
Resistance
Project: Chemical
Tank
Category: Acid Protection
Completion Date: August 2007
Job Description:
This company had a problem with the acid
eating away the stainless steel tank. The tank was cleaned
and roughed up with a grinder to give a strong bond. Then
it was coated with UCC CR9804 Chem Resist Ceramic. This will
extend the life of the tank and reduce maintenance. As well
as getting a tough coating with strong chemical resistance.
Ultimate
VE100
Corrosion, Chemical an Abrasion Resistant Composite With Quick
Return To Service
Majority of Service
Stations situated across Australia are suffering from water
contamination in their fuel cells. An Australian Company are
in the process of repairing all these tanks with reinforcement
and then placing a composite coating to protect the reinforcement
from being attack from corrosion and chemicals. VE100 was
chosen to perform these tasks. VE100 has been designed to
hold all sorts of Acids, Alkalis, Solvents, Hydrocarbons,
Ionised Water at all various concentrations and temperatures.
(115oC Full Immersion and 175oC Non Immersed Environments).
Before
After
|
